By-Pass Oil Filtration

By-Pass Oil Filter Systems

Engine wear is caused by dirt particles larger than 5 microns. By comparison, the average spin-on filter is rated at 25-40 microns. The AMSOIL By-Pass Oil Filter removes particles as small as 1/10 of a micron, and up to a pint of water, virtually eliminating engine wear. AMSOIL By-Pass Oil Filters filter all the oil in a six-quart system in about five minutes at an average engine speed equivalent to 45 mph. (All By-Pass Kits are transferable from vehicle to vehicle, so you never loose your investment!) See applications & configurations below.

By-Pass Oil Filter

Only minor mechanical ability is required for your application's installation!

"When we took this Chevrolet 396 engine apart (using AMSOIL Synthetic 10W-40, Reusable Air Filter and By-Pass Oil Filter), it was in the best condition of any engine I have ever seen. It looked like it had about 80,000 miles on it instead of over 535,000. The bearings were not even worn to the brass and the rings were not worn out. It was clean inside, no sludge or carbon at all."

K.A., Liberal, Kansas

Typical By-Pass Installations.


Frame Mount 1 Click for larger image	Frame Mount 2 Click for larger image	Under Hood Mount 1 Click for larger image

PRODUCT DESCRIPTION

The AMSOIL By-Pass Oil Filter provides the best possible filtration protection against wear, oil degradation, rust and corrosion. Working in conjunction with the engine’s full-flow oil filter, the AMSOIL By-Pass Filter operates by filtering oil on a "partial-flow" basis. It draws approximately ten percent of the oil at any one time and traps the extremely small, wear-causing contaminants and water that full-flow filters can’t remove. The AMSOIL By-Pass Filter typically filters all the oil in the system several times an hour, so the engine continuously receives analytically clean oil.

Typical By-Pass Circulation Diagram for BMK-11 & BMK-12

By-Pass Oil Filtration System Diagram

Typical Installation Diagram for BMK-11 and BMK-12 Kits.

Mounts are also available that connect directly to the engine's oil filter base, requiring minimal mechanical ability, and minimal installation time! See BMK-13, BMK-15 & BMK-16

By-Pass Filter Photos

BMK-11	BMK-12	BMK-13	BMK-15 & BMK-16


Sample Kit	Size Measurement

Reduces Wear

Approximately 60 percent of all engine wear is caused by dirt particles in the 5 to 20 micron range. These particles can get inside the precision clearances between engine components and cause severe damage. While full-flow oil filters generally stop contaminants no smaller than 25 to 40 microns, the AMSOIL By-Pass Filter effectively stops particles smaller than one micron in size, substantially reducing engine wear.

Prevents Oil Degradation, Rust and Corrosion

Water enters motor oil as a combustion by-product or as a condensate. Water contamination of the motor oil can cause extreme engine damage. Water causes metal surface rust and corrosion, which increases friction and wear and deteriorates the close-fitting tolerances between engine components. In addition, water reacts with other oil contaminants to form corrosive acids, which also damage metal components. The AMSOIL By-Pass Filter removes water, reducing the risk of oil degradation, engine rust and corrosion.

Extends Oil Drain Intervals

Because the AMSOIL By-Pass Oil Filter removes water and particles smaller than one micron, it significantly increases the time oil can safely be left in the engine. In fact , engines using AMSOIL Synthetic Motor Oil and an AMSOIL By-Pass Oil Filter routinely show much lower rates of engine wear - even when the oil is used for significantly longer drain intervals - than engines using conventional products and conventional oil drain intervals. That saves motorists time and money and helps protect the environment by creating substantially less used oil.

Dual Remote Filter System

The AMSOIL Dual Remote Oil Filtration System converts an engine’s full-flow oil filter system into a full-flow/by-pass oil filtration system by attaching an AMSOIL Full-Flow Oil Filter and AMSOIL Spin-On By-Pass Oil Filter onto a remote mount. The Dual Remote System provides superior filtration efficiency, increased oil capacity and improved oil filtration accessibility.

Typical Installation Diagram for
BMK-13, BMK-15 and BMK-16 Kits.

AMSOIL By-Pass Filter Replacement Chart

Type of Unit	Stock Number	Size (Approx.)	Additional Oil Needed	Crankcase Capacity	Normal Service Life ^b	Applications
SINGLE SPIN-ON ELEMENTS (Used with BMK-11 or any DUAL REMOTE SYSTEM)	BE-90	Diam. = 4.5 in. Height = 6 in. With Mnt. = 8 in.	1 qt.	up to 9 qt.	25,000 miles or 1 year (approximately 4 times normal drain interval)	Pleasure Vehicles, Light Trucks and Smaller Commercial Applications
	BE-100	Diam. = 4.5 in. Height = 8 in. With Mnt. = 10 in.	1.5 qt.	up to 15 qt.
	BE-110	Diam. = 4.5 in. Height = 10 in. With Mnt. = 12 in.	2 qt.	up to 21 qt.
DUAL SPIN-ON ELEMENT (Used with BMK-12 DUAL-GUARD)	(2) BE-90's	Diam. = 5 in. Height = 9.5 in. With Mnt. = 8 in.	2 qt.	15 to 18 qt.	2 times normal oil drain interval	Large Trucks, Construction, Farm and Industrial Equipment (minimum sump capacity = 15 qt.)
	(2) BE-100's	Diam. = 5 in. Height = 9.5 in. With Mnt. = 10 in.	3 qt.	15 to 30 qt.
	(2) BE-110's	Diam. = 5 in. Height = 9.5 in. With Mnt. = 12 in.	4 qt.	15 to 42 qt.
LARGE CANISTER BY-PASS FILTERS	BE-50	Diam. = 7.5 in. Length = 10 in.	8 qt.	15 to 30 qt.
LARGE CANISTER BY-PASS FILTERS	BE-75	Diam. = 7.5 in. Length = 15 in.	12 qt.	15 to 42 qt.

a. Filters can be used on sumps of larger capacity but then require more frequent replacement. Full details on service life included with filter installation instructions

b. Data determined in a non-turbo gasoline engine with AMSOIL 100% Synthetic Motor Oil and AMSOIL Full-Flow Oil Filter. Service life varies in other engines (turbo and diesel) and with other oils and filters.

NOTES:

1. Special adapters and hardware may be required for some installations.

2. Contact AMSOIL INC. Technical Service for instructions before installing on vehicles with cast aluminum oil pans.

APPLICATIONS

Mount	Filter (Order separately unless noted)
BMK-11	BE-90, 100, 110
BMK-13	BE-90, 100, 110 SDF-15, 26, 34, 42, 57, 84, 96
BMK-15 (complete with filters)	SDF-26 and BE-100 (Filters Included)
BMK-16 (complete with filters	SDF-26 and BE-100 (Filters Included)

Vehicles with sump capacities greater 15 qts.
Mount	Filter
BMK-12 Dual Guard	Any size AMSOIL Spin-On By-Pass (mount requires 2 filters and all hoses and fittings)
Heavy-Duty Canister Type (Element Only)	BE-50, BE-75 (Replacement Element only for Lubrifiner 500 and 750 respectively.)

For Immediate Application Assistance, and to generate a complete listing/summary of All Amsoil products for your vehicle, including lubrication recommendations, oil & air filters, spark plugs & wires, fill capacities, torque values and Amsoil maintenance intervals, etc., click this link to the

To obtain an immediate product order Quotation, including shipping charges, please visit my AMSOIL Online Store and fill out a quick order with bogus shorthand in required fields (a couple of fake letters), but completed picks of products to order, without any credit card info or final submission of the order for purchase. COOKIES must be enabled in your browser, to use the full features of browsing, application searches, or ordering products. If your browser's cookie feature is disabled, when a link is followed, a help screen will appear to help you instantly enable cookies. Then, after enabling cookies, come back to this page and follow the desired link again.